ALFACOM ENGINEERING LTD.
Bronze Valves
Explore bronze gate, globe and lift check valves, together with the brass water control products, level indication equipment and stainless steel screen listed in this catalogue family. Check the material and model-specific documentation for each item before selection.
Bronze Valves · Illustrative image
Explore Valves and Related Equipment
Choose by function below for English model details and technical documents. Body and component materials vary by model and size.
Bronze Isolation and Check Valves
CONTI 10250 · Bronze Gate Valve
CONTI 72452 · Bronze Globe Valve with PTFE Seat
Brass Water Control Valves
FARG 505 · Brass Water Pressure Reducing Valve
CONTI 90604 · Water Relief Valve
Level Indication and Related Accessories
CONTI 61506 · Brass Water Level Gauge Set
CONTI FIL77652 · Stainless Steel Check Valve Screen
CONTI 70656 — Bronze Horizontal Lift Check Valve
A screwed-end, spring-loaded lift check valve identified as PN25 in the drawing. The document lists a bronze C83600 body and a PTFE disc, with size-dependent component details.
Select the nominal size, thread form and permitted installation orientation. Use the drawing for dimensions and material details; confirm the required pressure-temperature duty for the supplied model.
CONTI 10250 — Bronze Gate Valve
A screwed-end bronze gate valve identified as PN20. The drawing specifies a bronze CB491K body, brass wedge and handwheel operation, with sizes listed from 1/4 to 4 inches.
For isolation service, specify connection size, thread form, fluid, pressure and temperature. Confirm the actual supplied configuration and installation dimensions from the technical drawing.
CONTI 72452 — Bronze Globe Valve with PTFE Disc
A screwed-end bronze globe valve identified as PN25. The drawing lists a bronze CB491K body and replaceable PTFE disc; bonnet and other component materials vary by size.
Specify nominal size, thread form and required duty. Check the dimensional drawing, materials and allowable operating conditions for the selected size.
FARG 505 — Water Pressure Reducing Valve
A piston-operated water pressure reducing valve with a compensation chamber, CW617N brass body and AISI 304 stainless steel seat. Male pipe unions use ISO 228/1 threads.
The factsheet lists 1/2 to 2 inch sizes, maximum recommended operating pressure 25 bar, maximum operating temperature 120°C and factory outlet setting 3 bar. The outlet adjustment range is 0.5–6 bar for 1/2 and 3/4 inch sizes, and 1–6 bar from 1 to 2 inches. Do not use in freezing conditions. Select the size using the required flow and inlet/outlet pressures.
CONTI VSI90604 — Water Relief Valve
A screwed-end relief valve identified as PN16 in the drawing. Body material is brass CW617N for 3/8 to 2 inch sizes, and bronze CB491K for 2 1/2 to 3 inch sizes.
State the fluid, required set pressure, relieving duty, connection size and documentation requirements. PN16 identifies the valve designation; it does not specify the requested set pressure or discharge capacity. Confirm those for the actual supplied valve.
CONTI INL61506 — Brass Water Level Indicator Set
The drawing identifies a brass level indicator with drain and male screwed ends, designated PN10. It distinguishes PS upper and PI lower components in 1/4, 3/8 and 1/2 inch sizes.
Specify the top and bottom arrangement, connection size and complete gauge assembly requirements. Confirm tube or glass dimensions, seals, service conditions and the components included in the supply.
CONTI FIL77652 — Check Valve Screen
The drawing shows an AISI 302 stainless steel screen with a Nylon screwed-end component. The listed nominal sizes extend from 1/2 to 4 inches.
Match the accessory to the original valve and connection geometry. Confirm the required filtration characteristics, fluid and temperature compatibility; the screen alone does not define a complete check-valve assembly.
APPLICATION BEFORE SPECIFICATION
Selection Starts with Your Application
Provide the fluid, corrosion conditions, pressure, temperature, size and connections. For seawater or other demanding service, confirm the exact alloy, seals and supporting manufacturer documentation.
Catalogue & Technical Documents
Review the model-specific technical information and installation requirements. Send a specification, drawing or existing model reference if you need help selecting equipment.
This drawing covers the CONTI 10250 bronze gate valve. Other model documents, where available, are linked from the individual product pages.
Discuss Your Application
Send your requirements or a photo of the existing equipment for technical assistance and a quotation.
Availability and lead time are confirmed for the requested model and quantity.